Collaboration diagram for STM32H7xx_System_Exported_Functions:

Functions
void	SystemInit (void)
	Setup the microcontroller system Initialize the FPU setting and vector table location configuration.
void	SystemCoreClockUpdate (void)
	Update SystemCoreClock variable according to Clock Register Values.
void	ExitRun0Mode (void)
	Exit Run* mode and Configure the system Power Supply.

Detailed Description

Function Documentation

◆ ExitRun0Mode()

void ExitRun0Mode ( void )

extern

Exit Run* mode and Configure the system Power Supply.

Note

This function exits the Run* mode and configures the system power supply according to the definition to be used at compilation preprocessing level. The application shall set one of the following configuration option:

PWR_LDO_SUPPLY
PWR_DIRECT_SMPS_SUPPLY
PWR_EXTERNAL_SOURCE_SUPPLY
PWR_SMPS_1V8_SUPPLIES_LDO
PWR_SMPS_2V5_SUPPLIES_LDO
PWR_SMPS_1V8_SUPPLIES_EXT_AND_LDO
PWR_SMPS_2V5_SUPPLIES_EXT_AND_LDO
PWR_SMPS_1V8_SUPPLIES_EXT
PWR_SMPS_2V5_SUPPLIES_EXT

The function modifies the PWR->CR3 register to enable or disable specific power supply modes and waits until the voltage level flag is set, indicating that the power supply configuration is stable.

Parameters

None

Return values

None

Definition at line 474 of file system_stm32h7xx.c.

References PWR, PWR_CR3_BYPASS, PWR_CR3_LDOEN, and PWR_CSR1_ACTVOSRDY.

◆ SystemCoreClockUpdate()

void SystemCoreClockUpdate ( void )

extern

Update SystemCoreClock variable according to Clock Register Values.

The SystemCoreClock variable contains the core clock , it can be used by the user application to setup the SysTick timer or configure other parameters.

Note: Each time the core clock changes, this function must be called to update SystemCoreClock variable value. Otherwise, any configuration based on this variable will be incorrect.; - The system frequency computed by this function is not the real frequency in the chip. It is calculated based on the predefined constant and the selected clock source:

If SYSCLK source is CSI, SystemCoreClock will contain the CSI_VALUE(*)
If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(**)
If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(***)
If SYSCLK source is PLL, SystemCoreClock will contain the CSI_VALUE(*), HSI_VALUE(**) or HSE_VALUE(***) multiplied/divided by the PLL factors.

(*) CSI_VALUE is a constant defined in stm32h7xx_hal.h file (default value 4 MHz) but the real value may vary depending on the variations in voltage and temperature. (**) HSI_VALUE is a constant defined in stm32h7xx_hal.h file (default value 64 MHz) but the real value may vary depending on the variations in voltage and temperature.

(***)HSE_VALUE is a constant defined in stm32h7xx_hal.h file (default value 25 MHz), user has to ensure that HSE_VALUE is same as the real frequency of the crystal used. Otherwise, this function may have wrong result.

The result of this function could be not correct when using fractional value for HSE crystal.
Parameters

None

Return values

None

Definition at line 352 of file system_stm32h7xx.c.

References CSI_VALUE, D1CorePrescTable, HSE_VALUE, HSI_VALUE, RCC, RCC_CFGR_SWS, RCC_CFGR_SWS_CSI, RCC_CFGR_SWS_HSE, RCC_CFGR_SWS_HSI, RCC_CFGR_SWS_PLL1, RCC_CR_HSIDIV, RCC_D1CFGR_D1CPRE, RCC_D1CFGR_D1CPRE_Pos, RCC_D1CFGR_HPRE, RCC_D1CFGR_HPRE_Pos, RCC_PLL1DIVR_N1, RCC_PLL1DIVR_P1, RCC_PLL1FRACR_FRACN1, RCC_PLLCFGR_PLL1FRACEN, RCC_PLLCFGR_PLL1FRACEN_Pos, RCC_PLLCKSELR_DIVM1, RCC_PLLCKSELR_PLLSRC, RCC_PLLCKSELR_PLLSRC_CSI, RCC_PLLCKSELR_PLLSRC_HSE, RCC_PLLCKSELR_PLLSRC_HSI, SystemCoreClock, and SystemD2Clock.

◆ SystemInit()

void SystemInit ( void )

extern

Setup the microcontroller system Initialize the FPU setting and vector table location configuration.

Parameters

None

Return values

None

Definition at line 178 of file system_stm32h7xx.c.

References __IO, CLEAR_BIT, DBGMCU, FLASH, FLASH_ACR_LATENCY, FLASH_LATENCY_DEFAULT, FMC_Bank1_R, MODIFY_REG, RCC, RCC_AHB2ENR_D2SRAM1EN, RCC_AHB2ENR_D2SRAM2EN, RCC_AHB3ENR_FMCEN, RCC_CR_HSION, READ_BIT, SCB, and SET_BIT.